These black protective sleeves are a perfect way to protect your rod
holders when they are not in use. This expandable sleeve will fit snugly
over the entire rod holder and will protect the tube from scratches, rub
marks and other blemishes.
The sleeve simply slides onto the rod holder to allow for easy
covering and removal. The top of the netting also folds inside the top
of the tube to protect the rim of the tube from damage.
Dropshipped directly from Cisco
Net Holder Track sold separately *Shown mounted in 6" Cisco track
Holders are great for holding large/heavy nets and storing them out of
the way when not in use.
Made entirely from aircraft grade anodized aluminum
A drain hole is conveniently located at the base of the tube
This aluminum cup holder is large enough to securely hold any
beverage can wrapped in a koozie and can be mounted to your boat in many
ways. Unlike other cup holders available a thick rubber coating is
applied around the rim of every cup holder for a safe and clean look.
Cup holders on track mounts can slide into any Bert's, Traxstech
or Cisco track system (similar models will fit as well) when mounted
to the track mount as shown in the photo.
Also sold for use with cross plates
On track mount $31.00
For use on cross plates $16.00
Dropshipped directly from Cisco/p>
These track backing plates are designed to reinforce each of the
mounting stress points the gunwale creates when heavy equipment is
mounted in the tracks. It is recommended that anyone running
dipsy rod holders or downriggers in their track reinforces the
underneath mounting hole locations whenever possible.
Made from solid aircraft grade aluminum
Each plate is 3" Long
6" Track - (2) Plates
12" Track - (3) Plates
18" Track - (3) Plates
24" Track - (4) Plates
36" Track - (4) Plates
48" Track - (5) Plates
60" Track - (6) Plates
72" Track - (7) Plates
Dropshipped directly from Cisco
Motor Stabilizer Mount
The trolling motor stabilizer
mount is extremely easy to use and heavily constructed for a LIFETIME of
use. It is able to safely secure any trolling motor arm from 7/8"
to 1-3/8" in diameter with no tools required!
Spring Loaded Locking Unit
Cisco's unique spring loaded mechanism means that you no
longer have to worry about aligning pieces and parts to support
your trolling motor arm; and this can especially difficult in
rough conditions. Simply lift up on the stainless steel
handle and turn it over the arm of the trolling motor and
release. The synthetic V-Channel safely cradles the arm
and the thick rubber adhesive on the stainless steel hook
protects the trolling arm from scratching while providing a snug
Easily Adjustable on all 3 axises
The arm of the mount is able to adjust to any angle
between 0 and 180°. The arm is held in place by a
pressure sensitive clamp which allows it to move freely when
enough pressure is applied on it, yet stay locked in placed
when it is holding the trolling motor arm. This means
that when fishing you can remove your trolling motor unit
and push on the mount to lay it down, making it great
for storage purposes! When you are ready, simply
lift up on the mount to lock your trolling motor in place,
and prepare to cruise along the water with peace of mind!
Vertical (Height) and Radial Adjustment
Cisco's innovative design not only allows you to adjust
to virtually any angle to accommodate various styles of
boats, but it also allows you to positions the unit to the
EXACT height required for proper
installation of the unit. The outer stabilizer tube
can be positioned to any height along the solid aluminum rod
and can rotate 360° to ensure that the trolling motor arm
fits precisely in the synthetic V-Channel. Once you
have the unit positioned vertically and radially it can be
locked in place by tightening the 4 set screws.
Available in 3 sizes. Measurements are from the bottom of
the round mounting plate to the bottom of the trolling motor arm.
Small - Adjusts for any height from 6" to 8"
Medium - Adjusts for any height from 8" to 12" **MOST
Large - Adjusts for any height from 12" to 17"
Silver: Small $73.50
Black: Small $78.50
Mast for GoPro® on a track mount is designed to hold any standard
GoPro® cameras at the top of the 36" handheld mast. The mast
pole is fitted with a soft grip foam handle and fits securely into a
base collar on a track mount (other mounts also available) for easy
storage when not filming. The mast pole is 5/8" diameter solid
anodized aluminum and is the perfect length for reaching those
awesome shots underwater while reeling in and netting fish!